Now for the right side

Everything looks good. Seems to be plenty of clearance. The right side should go faster, now that I know the pitfalls. The goal is to have everything forward of the roll bar completed by year's end.

Photos ???

I've probably mentioned this before, but the car was completely dismantled and later, reassembled to sell but never raced. So all the photos and notes taken might not be accurate. This is a issue I came across on the spacers used on the steering link that connects to the front bearing carrier. The old photos shows the spacer on the bottom. When connected there, it just throws everything off, and looking at photos of other Lola T190's 92's, it shows the spacer on the top, which works better. So for now I'm placing it on the top. When the right side suspension is on, I'll have a better idea. I think the bump steer is through these spacers? It's been awhile.

Front Suspension

Starting to place some of the front suspension hardware on the car. Temporary put in place just to make sure it all bolts together properly.

Rotor Time.

It's back to work. Pulled out the left front rotor from my boxes of many parts. Another one of those parts you forget about and realize it has to be inspected and cleaned up., and there's 3 more to do. Starting to think I better pickup the pace a bit, if I want to race next year.

12" Snow in October?

Tuesday looked like a tornado past through. The snow stuck to the leaves and just broke everything. The power to the house went out at noon on Tuesday and return late Thursday evening. However the shop where I keep the car is behind the house and has a separate electric line. Tree snapped it and now I'm still waiting for electric back there.

Fuel cells, steering rack.

Steering rack is installed, fuel cells front crossover plumbing all connected.

Can closeup the fuel cells now, and move to the left front suspension.

More Progress

Last week was productive. Clutch line is done, steering rack is ready for installation and gas, brake and clutch pedals are in and tight. Waiting on some hardware from "Pegasus" and "Air Craft Spruce".

Decals

It's starting to come together. But, as with everything else, it sure has taken a lot longer to accomplished.

I'm changing the route the left rear brake line takes. The old line went around the radiator cooling line(photo). The new line will stay along the tub, hoping this stays out of the way of parts, down the road. I purchased the car as a roller, so I have not photos of the car complete in this area.

Fuel cells and lines.

This week has been fairly productive. I did have to make a small adjustment to the front brake lines. I forgot the square radiator cooling lines run down the same channel as the brake lines and had to move the lines to the side. No big deal but still took a couple of hours. Before I tackle the rear lines I’ll take a real close look at my photos of this section and try to get it right the first time.
As you can see the fuel cells are installed. As mention in a earlier blog, make small modifications to the tub to accept the new cells. But they went right in on the first try, and fit perfect.

Brake Lines

Didn't think I would have anytime today for the car, but found about a hour and got the front brake lines done.

Brake Calipers and more.

Nothing like a rainy weekend to focus on the car. The parts for the brake calipers have been waiting for me, but are now assembled and finished. Also installed the clutch and brake pedals. Mounted the rebuilt master brake and clutch cylinders. Started on the brake line replacement and would like to have this done by weeks end.

Brakes & Decals

Finishing the final preparation of the master cylinder parts and pedal assemble. A lot of time goes into cleaning. Hope to have the master cylinders mounted by weeks end. Then I can start to run the new lines.

Just got back the decals, the shop did a fantastic job.

Looks just like the originals.

Reproduction Decals

I need two decals reproduced. One I had taken to a graphics shop "AUTOMOTIVE CHEMICALS" a while back, but they did a lousy job. The other is the 10" wide red, white, blue, yellow stripe. I'm trying a different shop. There taking a different approach and guarantee they will come out prefect. Find out next week.

Master Cylinders

Received the rebuilding kits for the master cylinders and clutch cylinder today. They didn't look to good coming off the car, but they cleaned up real nice and the bores look good. Hooked up the rest of the gear shift linkage, goes a lot faster when you know the procedure ahead of time.