I'll take what's behind door #2

I think this is my best option. Made temporary hardware and it looks OK. If I have a couple of small brackets made, the wing with the support should fit quite well. This modification is best left to the pro's.

Rear Wing

The rear wing has a issue that I have waited to tackle. When I went out to St. Louis to pickup the car, the rear wing was not attached, just sitting there on the floor with the boxes of spare parts. Once the car was home, I found out why. No way will the wing mount to the rear of the car, there's just no provisions for attachment. Upon closer examination of old photos, I realized that this particular wing was not used. So I placed all the spare parts on the floor that might have a connection.

I did come up with the old mounting hardware for the wing I don't have(photo). More tomorrow.

Bits & Pieces

There's lots of bits and pieces that need my attention. The fuel system with the exception of the cells and fuel filter where missing. So. I'm kinda in the dark, but I will put in a order for what I think I need and go from there. The car was run with fuel injection, but the replacement is way to expensive, so it's the Webers for now. The shift linkage is now in place, the final adjustment will be made at the track. Next week, attach the brake lines and test for leaks, and think about the seat belts, the club that I race with are requiring the Hans device beginning in August.

Has it been that long?

Almost 2 years later, the gearbox and tub are one unit. Now with the gearbox and suspension attached to the tub. Brake lines, clutch lines, shift linage, wires can all be connected.

Missing?

Before I can connect the gearbox to the chassis, I needed to make this small bushing. There's a aluminum plate that goes between the bell housing and engine. The plate contains 6 steel bushings that the attaching bolts go through, well I was missing one. Not 100% sure it was there when I dismantled the car. Fortunately I have a South Bend lathe that my father gave to me 35 years ago. One of those must have tools in your collection. But anyway, 2 hrs later(on the lathe) I had it replaced and ready to install.

Lucky 13

Graphics shop again did a real nice job. This number is on the nose. The photo to the left(1975), the number was probably hand painted

Last one done.

That's it for the wheels. All 4 done.

Just a little more.

It will still be awhile before I attach the rear to the tub, but placing it position helps to see what modifications might be needed. Needed to make new attaching bolts, the old ones where in pretty bad shape.

The big move!

There's not much more I can assemble on the rear. So it's time to position it behind the tub. I'll continue to use the table it's on now, and make the tub movable for aliment. It will be more visual in the next post.

Windshield installed.

Another one of those long projects that is finally completed.

New Windshield

The new windshield just arrived from LP Aero Plastics Inc. Placed it on the body and the size appears to be perfect. The one thing I still have to do is drill the holes for mounting. It looks opaque, but that's just the protective covering, it's clear.

Three down, one to go.

The rear rims are a bit bigger than the fronts. A whole lot more work to do.

Gearbox Plate

Studs are fitted and the gearbox plate installed. Rear suspension attached, and I guess for now ,this assembly is pretty much finished. There will be little odds and ends, but this will be needed to be fitted to the car and engine.

Starter Motor

Starter motor is overhauled, and ready to go.

More snow and cold weather.

Monday it snowed about 6" , windy and has been in the low teens. March has definitely arrived in as a Lion. On the phone with Jim the other day(engine rebuilder), looks like most of the engine I dropped off will be usable. The crank, block, heads, pan, are OK. The rods might be usable too. The pistons and cam will be replaced. The cam was real old school, it would have required very high revs to produce HP. This engine when completed should go the whole season with very little maintenance. Jim said next week he'll start assembling it.